
The IP•Express DLE1 interconnects remote LANs and addresses the large market for connectivity in the multi-megabit bandwidth range such as high quality MPEG Video delivery. The Integration of the E1 CSUs provides for a complete solution with a straight forward configuration. E1 Branch Office Connectivity:  Two E1 Inverse Packet Multiplexor: Inverse Packet Multiplexing is an option of the IP Express DLE1. IPM delivers 4 Megabits of interconnectivity over 2 Dedicated E1 WANs. IETF approved RFC1990 Multilink PPP protocol bonds multiple E1s into a high-speed link that has built-in redundancy. E1 line fault detection provides resilient connectivity for Mission Critical Interconnects. MPEG IP Multicast Streaming Video: IP Express DLE1-IPM models deliver MPEG IP Streaming Video over Inverse Packet Multiplexed T1s. The Inverse Packet Multiplexor provides the bandwidth necessary for the delivery of broadcast quality video feeds for a single MPEG Video. IP Multicast is a standard feature of the IP•Express DLE1 and is utilized to distribute MPEG video simultaneously to multiple decoders. MPEG IP Video Redundancy Switch: REDundant IP Video configuration automatically switches from the Primary to a Secondary Encoder's IP Video Stream for mission critical broadcasts and is available with the IP Express DLE1-IPM-RED. A one second absence of IP packets from the Primary Encoder results in the switch to the Secondary Encoder. The WAN bandwidth is reserved for a single feed. Technicial Specifications: LAN Network Interface: | - 10/100 BaseT Ethernet Port
- Auto-negotiate or Configured
Speed/Duplex
| LAN Network Protocols Supported: | - IP, TCP, UDP, RIP, ICMP
- IP Multicast support
- IP Video Stream Redundancy (Optional)
| WAN Network Interfaces: | - Four E1/FracE1 CSU/DSU ports
- Inverse Packet Multiplexing (Optional)
| WAN Network Protocols Supported: | - PPP (RFC 1548, RFC 1332, RFC 1334, PAP)
- Multilink PPP (RFC 1990)
- Frame Relay (ANSI ANNEX D, LMI, RFC 1420)
| Routing Protocols Supported: | | E1/Fractional E1 Specifications: | - Framing - CRC4 or FAS or UNFRAMED
- Coding - HDB3 or AMI
- Supports DS0 assignments from 1 to 32 (64Kbps to 2.048Mbps)
| E1 Diagnostic: | - Loopback Test
Network, Internal, Framer, Payload
- Bert Tests
2E07,2E11,2E15,QRSS
| TFTP Online Upgrade Capable: | - Fully operational during upgrade
| Network Security: | - Full On Source, Destination Address;
Port and Flag IP Packet filtering
- Network, Device and Application Layers.
| Dimensions:
| - 9" (L) x 7.3" (W) x 1.50" (H)
- 2 E1 Wan Connectivity in 1/2 of a 19" rack
| Management: | - Telnet support with Edit and Paste
Templates
- Console Port for Out of Band
Management
- SNMP support (MIB I, MIB II)
- Remote configuration, monitoring, & reset
| Regulatory: | - Safety -IEC60950
- EMC - CFR 47 Part 15 Sub Part B:2002
EN55022:1994+A1&A2 EN55024, ICES-003 1997 CISPR 22 Level A
- Telecom TBR12, TBR13
- CE
| Power: | - Locking Power Connector
- 12-24 VDC 1.0A
Ships with Universal Adapter
- Optional -48V 0.25 Amp
- Hot Standby with 2nd Power Module
|
How to Order: Part No | Description | Notes | 095-2048-0x | IP•Express DLE1, xE1 (x=1 - 2 Ports) | Base Model Specify # of E1 Ports Enabled | U95-2048-0x | IP•Express DLE1 E1 Port Upgrade | Enable Additional E1 Ports (up to 2) | Base Options | | Specify as suffix | IPM | Inverse Multiplexor Option | IPM 4 Mbps Interconnet over 2 Dedicated E1 WANs
| RED | MPEG IP Video REDundancy Switch | Secondary Encoder Traffic passed on failure of Primary Encoder | Power Options | | Specify as suffix | DCMOD | Power 12/30 VDC w LOCKING CONNNECTOR | Ships with Universal Adapter 90/240 50/60 | N48VDC | Power 12/30 VDC Stripped Wire Screw | | Rack Mount Option | Power Supply Module Negative 48 Volt DC | Isolated Negative 48 Volt Power Hot Standby | RACKMNT | | Specify as suffix | | 19" Wide Rack Mount Brackets | Enclosure Nut Serts Installed |
|